Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
M
Moofus02
I'm Awesome
·
From
Michigan
Joined
Sep 21, 2021
Last seen
Yesterday at 3:45 AM
Messages
255
Reaction score
341
Points
63
Find
Find content
Find all content by Moofus02
Find all threads by Moofus02
Latest activity
Postings
About
M
Moofus02
reacted to
L31MaxExpress's post
in the thread
Gas Mileage
with
Like
.
It is an early TBI. Those had a speedo cable up until GM started adding rear wheel antilock brakes. Most of those V-series trucks and...
Yesterday at 3:45 AM
M
Moofus02
reacted to
L31MaxExpress's post
in the thread
L29 intake manifold question
with
Like
.
Not cheap but I have seen a couple of guys over the years that have sent the L29 manifolds to get them extrude honed. Pretty decent...
Monday at 12:50 AM
M
Moofus02
reacted to
L31MaxExpress's post
in the thread
How To: Ditch EFI and keep TBI PCM for 4L60E Control.
with
Like
.
Yes I did and the Pseudo highway mode works great provided the VE table is properly tuned.
Monday at 12:46 AM
M
Moofus02
reacted to
tayto's post
in the thread
How To: Ditch EFI and keep TBI PCM for 4L60E Control.
with
Like
.
Fast355 posted many years ago a pseudo highway mode in the 7427 if you MUST have it. you can also run open loop and set the fuel ratio...
Sunday at 1:49 PM
M
Moofus02
reacted to
Supercharged111's post
in the thread
350 stroker build (ca smog legal?)
with
Like
.
For me it was half a rib. Unbeknownst to me my Camaro came with an OBDII hub but was OBDI, so same thing opposite direction. Make sure...
Saturday at 3:47 PM
M
Moofus02
reacted to
L31MaxExpress's post
in the thread
350 stroker build (ca smog legal?)
with
Like
.
A standard SBC balancer has to be cut down by the width of the reluctor, IIRC it is like 0.110" thick where it sandwhiches between the...
Saturday at 3:47 PM
M
Moofus02
reacted to
Gordy_'s post
in the thread
350 swap?
with
Like
.
My main reasoning for the sniper is ease of installation. I hate dealing with woring and computers, so the sniper efi would be so much...
Saturday at 11:06 AM
M
Moofus02
replied to the thread
350 swap?
.
I would do the ebl personally if it had a stick. Tunable with knock protection
Friday at 8:29 PM
M
Moofus02
reacted to
PlayingWithTBI's post
in the thread
350 swap?
with
Like
.
I'm curious, what does the Sniper do better than the EBL with a WBO2? I'm not that familiar with the Sniper.
Friday at 8:27 PM
M
Moofus02
replied to the thread
350 swap?
.
You could also use elb flash with a tbi setup but it doesn't quite self tune like the sniper
Friday at 4:37 PM
M
Moofus02
reacted to
fancyTBI's post
in the thread
350 swap?
with
Like
.
You are right. OP, I can’t help with much of the wiring on that (what’s different, what’s the same) but the hard parts I listed should...
Friday at 4:35 PM
M
Moofus02
reacted to
Drunkcanuk's post
in the thread
350 swap?
with
Like
.
He's planning on using a Holley Sniper I believe.
Friday at 4:35 PM
M
Moofus02
reacted to
Schurkey's post
in the thread
350 swap?
with
Like
.
Don't forget the pilot bearing/bushing in the back of the crankshaft. "Good luck" with the Sniper.
Friday at 4:35 PM
M
Moofus02
reacted to
Drunkcanuk's post
in the thread
350 swap?
with
Like
.
As long as you are staying with the same transmission, all good on the driveshaft. You will need new motor mounts as @Moofus02...
Friday at 1:02 AM
M
Moofus02
reacted to
Spareparts's post
in the thread
Another 454 Vortec Build Thread - Documenting, Q&A, Help
with
Like
.
What do you mean 4 psi low with return line punched off? If the fuel pump return line is actually pinched off the pressure should jump...
Friday at 12:05 AM
Loading…
Loading…
Latest posts
9
Map Sensor Code Dying at Idle
Latest: 95 Tahoe
A moment ago
Engine Performance + Maintenance
Smeding Performance 383 in a 97 C1500
Latest: supspt454
3 minutes ago
Engine Performance + Maintenance
How much paint?
Latest: Drunkcanuk
3 minutes ago
Paint / Body / Detailing
Gas Mileage
Latest: 0xDEADBEEF
4 minutes ago
Engine Performance + Maintenance
S
7.4L vortec hard start
Latest: Stephen
5 minutes ago
Engine Performance + Maintenance
Staff online
df2x4
4L60E Destroyer
kennythewelder
Officially Retired, B31-3 (6-G) certified welder.
Members online
99xcss4
0xDEADBEEF
Nicks2drtahoe
vince72
95 Tahoe
Murphdawg19
nemec
studigggs
df2x4
toad1
BuiltToWork
Pinger
Frankofalltrades
Zavalaj05
DeCaff2007
OutlawDrifter
kennythewelder
Snowboi
454cid
supspt454
Drunkcanuk
FLGS400
EDNY
Stephen
Rocc bottom
Max Boost
Reega
squeasel
Stumpy
supertech
aldang25879
TICK
BVRPLZR
Beason
tayto
fancyTBI
Dyldog
caw_86
skylark
Dropped88
termite
Supercharged111
joelabella
Miahjoe
sled
Scupper
packer0440
DontPressureMe
AK49BWL
Chevyman1969
... and 28 more.
Forum statistics
Threads
64,556
Messages
1,396,503
Members
51,989
Latest member
Dyldog
Share this page
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
Top