Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Schurkey's latest activity
Schurkey
replied to the thread
Low Brake Pedal- finding resolution
.
If you clamp the front LEFT hose, does it also improve as much? How about the rear hose? Perhaps the caliper piston is not sliding...
Jul 15, 2024
Schurkey
reacted to
termite's post
in the thread
Low Brake Pedal- finding resolution
with
Like
.
Throwing this out there, we've all done it at least once. Bleeder is mounted on top of the caliper, correct? Possibility the caliper...
Jul 15, 2024
Schurkey
replied to the thread
Rear disc brake conversion makes loud humming noise
.
FIFY. It's a damned shame you paid good money for a bum conversion kit. First Guess: You didn't hammer the pads tight to the caliper...
Jul 15, 2024
Schurkey
reacted to
Erik the Awful's post
in the thread
Rear disc brake conversion makes loud humming noise
with
Like
.
Try cleaning the rotors thoroughly with rubbing alcohol, mineral spirits, or brake cleaner. Then scuff the rotor surfaces with emery...
Jul 15, 2024
Schurkey
replied to the thread
Still air in brakes after bleeding for a week
.
WHAT VEHICLE? The '98 C1500 in your signature? WHAT BRAKE OPTION CODE? Kinda guessing JB5. GM recommendation is to bleed an entire...
Jul 15, 2024
Schurkey
replied to the thread
Whistling/squealing sound starting at 20mph
.
Does it whistle with vehicle speed, or with engine speed? If you run the engine in neutral, vehicle stopped, at the same rpm as it's...
Jul 15, 2024
Schurkey
replied to the thread
Rough country lift kit? Or keep it stock?
.
1. Why do you need more ground clearance? 2. Why do you need bigger tires? 3. ON A 2WD TRUCK??? MOST guys who "lift" their trucks...
Jul 15, 2024
Schurkey
replied to the thread
7.4 distributor/cam damage
.
The ignition timing is NOT ADJUSTABLE. You cannot "set the timing". Turning the distributor housing adjusts the cam sensor...
Jul 15, 2024
Schurkey
replied to the thread
No Spark on 96 GMC with 5.0
.
Are ALL the fuses good? Is there power to the ignition coil? When you have the scan tool connected, does the computer have an RPM...
Jul 15, 2024
Schurkey
replied to the thread
Gas gauge acting up
.
Any chance you have about half-a-tank of fuel? That would explain the gauge showing...about half a tank. Have you filled the tank to...
Jul 15, 2024
Schurkey
replied to the thread
Is my 350 Misfiring?
.
WHAT VEHICLE?
Jul 15, 2024
Schurkey
replied to the thread
Hesitation and no power
.
Bank 1 fuel trims are much different from Bank 2. There can be several reasons for this--O2 sensor problems, injector problems, misfire...
Jul 15, 2024
Schurkey
reacted to
1998_K1500_Sub's post
in the thread
Hesitation and no power
with
Like
.
Bank 1 fuel trim looks funky to me... but nobody else said anything about it so... Coolant temp shows 66C --> 150F. If the...
Jul 15, 2024
Schurkey
replied to the thread
1995 K1500 TBI Surges Under Load after warmed up
.
FIFY. Overall, this truck is crying out for a scan tool and fuel-pressure test.
Jul 15, 2024
Schurkey
replied to the thread
4.3 Running rich
.
Install scan tool, look at the data stream. Are 3, 4, and 6 fed from the same plane of the intake manifold? (and therefore the same...
Jul 15, 2024
Latest posts
K
09 Escalade to 95 Yukon total conversion
Latest: kage898
A moment ago
OEM and Custom Interiors
Waste wages.
Latest: Scooterwrench
1 minute ago
Member Trucks
TBI / ECM tuning options. Chip / Burn / etc.
Latest: Scooterwrench
12 minutes ago
Engine Performance + Maintenance
Slop in brand new Borgeson quick ratio box
Latest: Caman96
19 minutes ago
Stock Suspension + Bolt On Kits
My Crimson Cruiser - 1996 GMC 1500 Project
Latest: fancyTBI
30 minutes ago
Member Trucks
Staff online
df2x4
4L60E Destroyer
kennythewelder
Officially Retired, B31-3 (6-G) certified welder.
Members online
Patina56
kage898
99xcss4
Sean Buick 76
wnd lop
Rock Hard Concrete
Scooterwrench
OBSOkie
mikentosh
Dylan101
Miiike
Gonzaga Lobos
Bluegmt400
Charlesteneows
boy&hisdogs
Drop2000
Minn95Dually
Drunkcanuk
Zimmerly
Komet
IndexOf0
Seymorey
454cid
Planb_smoothie
LTC_
df2x4
slowfivespeed
Gravyyy
calebsrepair
Yeetsmyfeets
orangeman
elninodeoro
kennythewelder
Caman96
Asylestru
nyceguy01
DonnieWest
AlohaOBS
MorrissNoups
Gibson
Schurkey
RMasala
wasted wages
lbeninger
movietvet
fancyTBI
Forum statistics
Threads
66,910
Messages
1,436,974
Members
56,926
Latest member
kage898
Share this page
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
Top