Recent content by man-a-fre

  1. M

    What is the new go to fuel pump still made?

    Just got another obs 1993 reg cab stock 5.7 c1500 seen the ac ep381 isnt readily available and ac may not be the best choice anymore , read alot on Delphi quality dwinding ,Carter has the p9005 but not much said good or bad about that pump. The Carter is made in China along with all of them i...
  2. M

    Does dashskin have any new discount codes?

    Need to order a Dashskin and they have a spot for a discount code on order form but I can't seem to find any does anyone have a good code for them?
  3. M

    Recommendations for dash cover

    Me too!! Looks times better than the cracked dash and has the defrost bars incorporated into the cover.
  4. M

    Anyone used the United Motor Products coil c535

    Yes ordered the United just now.
  5. M

    Anyone used the United Motor Products coil c535

    Thanks , but that coil isn't right for a 1994 .
  6. M

    Anyone used the United Motor Products coil c535

    Yes I have had good luck with the cap and rotor for 2 years, called them on the coil and it's made in China which kinda scares me that is seems to be the norm with coils.
  7. M

    Anyone used the United Motor Products coil c535

    Just wondering if anyone has has good luck with the United Motor Products coils , I am looking at thepart number c535 for my 1994 K1500 tbi 350 and was wondering if it would be a reliable choice?
  8. M

    Confirmed brake bleeding scan tools

    So will the mt2500 with this cartridge for sure cycle the isolation dump valve on a rwal 1994 k1500?
  9. M

    What is a good o2 crosscount number for a 1994 350 tbi

    Thank you Schurkey!
  10. M

    What is a good o2 crosscount number for a 1994 350 tbi

    I was just wondering what is a very good closed loop heated o2 sensor crosscount numbers for a 1994 350 tbi k1500 and what would be a time to change 02 sensor numbers, like how fast should I see the numbers tally on the display when I am driving. Mine are over 200 in a 3 minute drive with a new...
  11. M

    Tbi distributor magnet protection from rust question

    Thanks , I won't have to worry about that I have a new shaft and magnet I am installing in place of the old cracked magnet so I will spray it before installing , I am just trying to be proactive to try and keep the magnet portion from getting so rusty like the orignal I'm replacing.
  12. M

    Tbi distributor magnet protection from rust question

    Thanks for the replies looks like I'll try aerosol clearcoat I guess.
  13. M

    Tbi distributor magnet protection from rust question

    I was wondering what I can apply to the new distributor shaft magnet on my 1994 tbi 350 to try to keep it from rust jacking and cracking the new magnet on my new shaft . Was thinking spraying it with wd40 or fluid film, would this be a bad thing to do? Would spraying aerosol clear coat work ...
  14. M

    86 yr old shadetree knuckle buster.

    I have 2 94's and neither had it done. I still have to take the other one in for the switch replace. Hope this helps others get the switch recall sorted out . P.S old MXer I just restored a 82 Yamaha yz250j that ive had for a while,fun bike and fast.
  15. M

    86 yr old shadetree knuckle buster.

    They replaced my working brake switch at the dealer recently on my 1994 rcsb because it had an open recall campaign tsb #98065 might check it out , guess they had a couple wires they had to reverse in the plug also that gm wired wrong. It's all free you might check into it if your truck hasn't...
See more

Latest posts

Members online

... and 18 more.
Total: 1,295 (members: 68, guests: 1,227)

Forum statistics

Threads
64,734
Messages
1,399,626
Members
52,321
Latest member
AustinRay90

Share this page

Top