Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
mdnky's latest activity
mdnky
reacted to
Salty K1500's post
in the thread
97 K1500 DD/Overlander
with
Like
.
Looks like you got it figured out, I look forward to seeing your repairs. I was lucky that the rear section of my frame was just a...
May 1, 2024
mdnky
reacted to
Erik the Awful's post
in the thread
Best engine swap for 1990 gmc 5 speed manual
with
Like
.
You're starting with a 4wd truck. It's no Tundra, but it's still going to be heavy, no matter what. You don't need horsepower, you need...
Apr 28, 2024
mdnky
reacted to
Moofus02's post
in the thread
Best engine swap for 1990 gmc 5 speed manual
with
Like
.
How are you planning on using this truck. You put big power and torque in it and drive it hard you'll find the week spot in the...
Apr 28, 2024
mdnky
reacted to
618 Syndicate's post
in the thread
5.3 + manual swap
with
Like
.
Don't be afraid of the smaller motors. You can build a better 4.8/5.3 for the cost of a stock 6.0, Also remember that GM put 4.8's and...
Apr 28, 2024
mdnky
reacted to
Erik the Awful's post
in the thread
IRS in a gmt400
with
Like
.
Buy two. Whenever you run out, you have a spare available, and then you replace the spent reel immediately. I learned this the hard way...
Apr 27, 2024
mdnky
reacted to
Alteca's post
in the thread
IRS in a gmt400
with
Like
.
Some of the prettiest welds on the truck and they will never be seen once this bracket is installed.
Apr 27, 2024
mdnky
reacted to
GrimsterGMC's post
in the thread
IRS in a gmt400
with
Like
.
Nice welds mate.
Apr 27, 2024
mdnky
reacted to
GrimsterGMC's post
in the thread
IRS in a gmt400
with
Like
.
I use deer skin gloves, they are thinner so beware off picking up hot stuff as they really only keep the UV light off your skin. Do you...
Apr 27, 2024
mdnky
reacted to
GrimsterGMC's post
in the thread
IRS in a gmt400
with
Like
.
Once you get the basic settings in then it's just practice, and over time you will develop a technique that works for you as everyone is...
Apr 27, 2024
mdnky
reacted to
Alteca's post
in the thread
IRS in a gmt400
with
Like
.
The tbi is definitely great for what it’s intended to do and i loved it for a long time, but it’s about time for it to go… need to make...
Apr 27, 2024
mdnky
reacted to
Alteca's post
in the thread
IRS in a gmt400
with
Like
.
Well I’ve put a few thousand miles on the irs swap, including a pot hole or two and it’s still holding strong.
Apr 27, 2024
mdnky
reacted to
Alteca's post
in the thread
IRS in a gmt400
with
Like
.
I have a few reasons I’m debating doing the IRS. I’ve seen it done on c10s and the results seem to be great as far as handling and ride...
Apr 27, 2024
mdnky
reacted to
618 Syndicate's post
in the thread
IRS in a gmt400
with
Like
.
It's been covered on this site before, but one of the Van Halen trucks had IRS from a Corvette under it. Along with other drivetrain...
Apr 27, 2024
mdnky
reacted to
Alteca's post
in the thread
IRS in a gmt400
with
Like
.
This is a 6th gen subframe, seems fairly straightforward to mount as it’s only welding some tabs to the frame and 4 bolts holding it...
Apr 27, 2024
mdnky
reacted to
Schurkey's post
in the thread
gear ratio help for a newbie
with
Like
.
Yes, that axle is junk. It's a hand-grenade with the pin out. In most cases, they came with crappy rear brakes, too. GM had no...
Apr 27, 2024
Latest posts
N
1998 push 3 button 1500 stuck in 4low.
Latest: Nad_Yvalhosert
2 minutes ago
Transfer Cases
T
1998 k1500 5.7 with 4L60E wiring/shift issues
Latest: Tonkaobs
3 minutes ago
Transmissions
Mechanical Water Temp Gauge
Latest: 454cid
6 minutes ago
Engine Performance + Maintenance
Daily truck pics
Latest: JS45
24 minutes ago
Car / Truck Photos and Videos
Confused
Latest: Hipster
29 minutes ago
Axles + Brakes
Staff online
kennythewelder
Officially Retired, B31-3 (6-G) certified welder.
Members online
PM18S4
Tonkaobs
Sabinoerc
Miahjoe
Yeetsmyfeets
chevykid65
PlayingWithTBI
strikk
dkeyes25
Georgiabigfoot
Shipley4life
Pig929
99xcss4
Nad_Yvalhosert
El Tigre
johnckhall
caw_86
Travon
Keeper
jm101
Orpedcrow
Hipster
RideHighBlazer94
454cid
cable
Eeyore79
WojTec
Tan1998K2500
HardDriver
Green1998
BCChevyZ71
Cunhaleighton1991
Cadmaro
JS45
Spareparts
KMo_00
Drunkcanuk
Caman96
registered-bum
k-web
Fullsize
MagnusHaugen
Arek73151
Das Hatt
kennythewelder
Vddiaz94
heskahoka
Senior2Door
dhworkin
Charlesteneows
... and 21 more.
Forum statistics
Threads
64,745
Messages
1,399,852
Members
52,359
Latest member
HardDriver
Share this page
Facebook
X (Twitter)
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
Members
Top