Recent content by docstoy

  1. D

    Cylinder Compression

    For whatever reason it seems you have a valve problem and you found it.
  2. D

    Cylinder Compression

    I would be hoping to hear air movement thru the valves (intake or exhaust ) or thru the crankshaft area if going by the rings, or if you have long block together , thru intake or exhaust port at cylinder head or lower area of engine, I've never tried that with oil pan installed think it would be...
  3. D

    Cylinder Compression

    If problem seems to be on #1 and #8 , then back valves adjustment on those 2 cylinders, leave spark plugs out, rotate crankshaft , air should just be flowing thru sparkplug hole , if stillno air flow (compression) install spark plug for that cylinder , air will either come out around rings or...
  4. D

    AC issue replaced everything

    When you replaced your condenser did you ck to see if replacement condenser already had orifice tube installed ? If it didn't, did you install orifice tube correctly ? I'm thinking long end of orifice tube goes toward condenser .
  5. D

    Wiring issues

    You have been given some very good instructions on how to locate your problems . You have to look at your problems 1 circuit at a time and not get side tracked by everything else going on . You need to concentrate on using the wiring diagrams as your source of information , if you enable a...
  6. D

    1988 350 tbi sputters while accelerating

    I would suggest looking at grounds , making sure they are clean and tight , also download service manual for your year truck , look at symptoms page in driveability section , the manuals will also give locations of grounds . It was not unusual for first years of tbi for it to have 2 to 3 second...
  7. D

    5.7 Vortec intermittent long crank --> crank no start, backfires, clunking

    Don't hold on to wire or you will have sore arm . It will knock the sh_ _ out of you !!!
  8. D

    Frankenstein ? K2500 8600 gvw mismatched lower control arms

    HEE HAW !!!! Now clean up ,paint , replace ball joints and bushings . Thanks for reply , offroadtahoe
  9. D

    Frankenstein ? K2500 8600 gvw mismatched lower control arms

    So will forged lower control arms out of a '97 k2500 suburban work on my '93 k2500 8600gvw pickup ?
  10. D

    1994 k1500 wild misfire

    First question on last post, OE never used rtv on throttle body or gasket, just clean flat surfaces, if you have areas that are not flat then could be from improper removal of gasket or debris, you can fill areas that aren't flat but remove excess so you will have flat surfaces. Second question...
  11. D

    Hello my cheyenne 97 idle rough and accelerate poorly. At idle it sound like it as a cam in it.

    Having good information is key to being able to figure out problems with your vehicle, oe manuals do this because they give key information for service technicians fixing there vehicles. OEM don't like paying techs for swag repair and techs don't like to work on comebacks, you don't make money...
  12. D

    Wiring issues

    Glad you found some of it !!!
  13. D

    Parting out 97 k3500 W/T

    What about lower control arms ?
  14. D

    P0300 but seeing cylinder 4 misfire

    Looks like you got her apart , looks like a vortex, when you repost what truck is it and power train .
  15. D

    Truck runs ok for two days then like crap again out of nowhere

    Your last thread was about low idle speed think it's 3 pages over in threads . So what tools do you have ? Do you have access to a scanner ? Describe your problem in detail, and tell us again what year truck and power train.
See more

Latest posts

Staff online

Members online

... and 13 more.
Total: 1,703 (members: 63, guests: 1,640)

Forum statistics

Threads
64,975
Messages
1,403,827
Members
52,865
Latest member
redd29229

Share this page

Top